Initial commit

solar_panel.X/mcc_generated_files/device_config.c

@@ -0,0 +1,76 @@
+/**
+  @Generated PIC10 / PIC12 / PIC16 / PIC18 MCUs Source File
+
+  @Company:
+    Microchip Technology Inc.
+
+  @File Name:
+    mcc.c
+
+  @Summary:
+    This is the device_config.c file generated using PIC10 / PIC12 / PIC16 / PIC18 MCUs
+
+  @Description:
+    This header file provides implementations for driver APIs for all modules selected in the GUI.
+    Generation Information :
+        Product Revision  :  PIC10 / PIC12 / PIC16 / PIC18 MCUs - 1.81.8
+        Device            :  PIC18F97J60
+        Driver Version    :  2.00
+    The generated drivers are tested against the following:
+        Compiler          :  XC8 2.36 and above or later
+        MPLAB             :  MPLAB X 6.00
+*/
+
+/*
+    (c) 2018 Microchip Technology Inc. and its subsidiaries. 
+    
+    Subject to your compliance with these terms, you may use Microchip software and any 
+    derivatives exclusively with Microchip products. It is your responsibility to comply with third party 
+    license terms applicable to your use of third party software (including open source software) that 
+    may accompany Microchip software.
+    
+    THIS SOFTWARE IS SUPPLIED BY MICROCHIP "AS IS". NO WARRANTIES, WHETHER 
+    EXPRESS, IMPLIED OR STATUTORY, APPLY TO THIS SOFTWARE, INCLUDING ANY 
+    IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY, AND FITNESS 
+    FOR A PARTICULAR PURPOSE.
+    
+    IN NO EVENT WILL MICROCHIP BE LIABLE FOR ANY INDIRECT, SPECIAL, PUNITIVE, 
+    INCIDENTAL OR CONSEQUENTIAL LOSS, DAMAGE, COST OR EXPENSE OF ANY KIND 
+    WHATSOEVER RELATED TO THE SOFTWARE, HOWEVER CAUSED, EVEN IF MICROCHIP 
+    HAS BEEN ADVISED OF THE POSSIBILITY OR THE DAMAGES ARE FORESEEABLE. TO 
+    THE FULLEST EXTENT ALLOWED BY LAW, MICROCHIP'S TOTAL LIABILITY ON ALL 
+    CLAIMS IN ANY WAY RELATED TO THIS SOFTWARE WILL NOT EXCEED THE AMOUNT 
+    OF FEES, IF ANY, THAT YOU HAVE PAID DIRECTLY TO MICROCHIP FOR THIS 
+    SOFTWARE.
+*/
+
+// Configuration bits: selected in the GUI
+
+// CONFIG1L
+#pragma config WDT = OFF    // Watchdog Timer Enable bit->WDT disabled (control is placed on SWDTEN bit)
+#pragma config STVR = ON    // Stack Overflow/Underflow Reset Enable bit->Reset on stack overflow/underflow enabled
+#pragma config XINST = OFF    // Extended Instruction Set Enable bit->Instruction set extension and Indexed Addressing mode disabled (Legacy mode)
+#pragma config DEBUG = OFF    // Background Debugger Enable bit->Background debugger disabled; RB6 and RB7 configured as general purpose I/O pins
+
+// CONFIG1H
+#pragma config CP0 = OFF    // Code Protection bit->Program memory is not code-protected
+
+// CONFIG2L
+#pragma config FOSC = HS    // Oscillator Selection bits->HS oscillator
+#pragma config FOSC2 = ON    // Default/Reset System Clock Select bit->Clock selected by FOSC1:FOSC0 as system clock is enabled when OSCCON<1:0> = 00
+#pragma config FCMEN = ON    // Fail-Safe Clock Monitor Enable->Fail-Safe Clock Monitor enabled
+#pragma config IESO = ON    // Two-Speed Start-up (Internal/External Oscillator Switchover) Control bit->Two-Speed Start-up enabled
+
+// CONFIG2H
+#pragma config WDTPS = 32768    // Watchdog Timer Postscaler Select bits->1:32768
+
+// CONFIG3L
+#pragma config EASHFT = ON    // External Address Bus Shift Enable bit->Address shifting enabled; address on external bus is offset to start at 000000h
+#pragma config MODE = MM    // External Memory Bus->Microcontroller mode, external bus disabled
+#pragma config BW = 16    // Data Bus Width Select bit->16-Bit Data Width mode
+#pragma config WAIT = OFF    // External Bus Wait Enable bit->Wait states for operations on external memory bus disabled
+
+// CONFIG3H
+#pragma config CCP2MX = ON    // ECCP2 MUX bit->ECCP2/P2A is multiplexed with RC1
+#pragma config ECCPMX = ON    // ECCP MUX bit->ECCP1 outputs (P1B/P1C) are multiplexed with RE6 and RE5; ECCP3 outputs (P3B/P3C) are multiplexed with RE4 and RE3
+#pragma config ETHLED = ON    // Ethernet LED Enable bit->RA0/RA1 are multiplexed with LEDA/LEDB when Ethernet module is enabled and function as I/O when Ethernet is disabled